Workshop & garage heating · Scotland

Workshop & Garage Heating in Scotland

Infrared heating designed for the people at the bench, the ramp and the workstation – not for the roof space above them.

Established 2018 · Rosyth, FifeMCS certified NAP-69114RECC member 00077727

Why workshops and garages are so hard to heat

  • Warm air rises to the roof and the floor stays cold where people actually work.
  • Every time the roller door opens, the heat you have paid for goes straight outside.
  • Staff wear jackets all day, hands go cold and work slows down in winter.
  • Portable gas or diesel heaters bring fumes, moisture, noise and fuel handling into the workspace.
  • Only a few benches or bays are used at once, but the whole building is being heated.
  • Uninsulated walls and roofs, high eaves and draughty doors make conventional systems slow and costly to run.

Infrared heaters warm people, tools, vehicles and surfaces directly, in the same way the sun warms you on a cold, clear day. Because the heat is not carried by the air, it is far less affected by an open roller door or a high roof – so you can heat the bays and benches that are occupied, when they are occupied. We will always tell you honestly if infrared is not the right answer for your building.

Infrared ceiling heaters in a workshop – installed by Scottish Energy Saving
Ceiling-mounted infrared heaters in a workshop installed by SES

The SES engineering process

We are an engineering-led heating installer, not a heater supplier. Every workshop system is designed around the building, the work carried out in it and the people using it.

Building assessment

Construction, insulation, roof and eaves height, doors, layout, working areas, occupancy hours and how the space is actually used.

Preliminary heating design

A draft layout showing proposed heater positions and heating zones, so you can see exactly what is planned before any commitment.

Heat-loss assessment

Where a space needs background heating as well as heating for occupied zones, we assess losses through the fabric, ventilation and air leakage.

Heater selection

Heater type and output chosen for each zone, taking into account dust, moisture, vehicle movements and how robust the unit needs to be.

Mounting height

Set for the people being heated and kept clear of vehicle lifts, cranes, racking and roller doors.

Electrical capacity

We check your incoming supply and distribution board, including three-phase supplies, and flag any upgrade or new circuits needed before we quote.

Controls & zoning

Timers, thermostats and zone controls that staff can operate easily, so heat is only used where and when it is needed.

Installation

By qualified electricians, planned around your working day and phased bay by bay if the workshop needs to stay open.

Testing

Full testing and commissioning of every circuit, heater and control before handover.

Certification

Electrical certification and a handover showing you how to use and adjust the controls.

Who we design workshop heating for

Vehicle garages & MOT bays

Repair garages, MOT bays and body shops (spray booths need specialist equipment).

Fabrication & joinery

Joinery, fabrication and engineering workshops heated bench by bench.

Agricultural & plant

Agricultural and plant workshops with large doors and high roofs.

Industrial units

Light manufacturing and trade units on business parks.

Community workshops

Maker spaces and Men’s Sheds used at set times each week.

Home garages & workshops

Larger domestic garages and home workshops – same survey and design approach.

Heating a larger storage or production building? See warehouse and industrial heating or commercial infrared heating.

Workshops and industrial units we have heated

Photographs from genuine SES workshop and industrial installations.

Infrared ceiling heaters in a workshop – installed by Scottish Energy Saving
Workshop – ceiling-mounted heaters
Infrared heaters in an industrial unit – installed by Scottish Energy Saving
Industrial unit – zoned radiant heating
High-output infrared wall heaters – installed by Scottish Energy Saving
High-output wall-mounted heaters
Infrared heating zone controller – installed by Scottish Energy Saving
Zone controls staff can operate easily

Guarantees & accreditation

Infrared heating panels supplied by SES carry a 5-year guarantee. All installations carry a 2-year workmanship guarantee and a 2-year insurance-backed guarantee. Scottish Energy Saving is MCS certified (NAP-69114), NAPIT registered and a member of RECC (00077727).

MCS certified installerNAPIT registeredRECC memberTrading Standards Approved Code

Workshop and garage heating FAQs

Will infrared still work when the roller door is open?

Infrared heats people and surfaces rather than the air, so opening a door has much less effect on comfort than it does with warm-air heating. It will not stop cold air coming in, so we take door positions and how often they open into account when we place heaters and set zones.

Can you heat just the benches or bays we use?

Yes. Zoning is central to how we design workshop systems. Each bay, bench or work area can be controlled separately, so unused areas do not need to be heated.

How high can the heaters be mounted?

It depends on the heater type, its output and the area it needs to cover. We set mounting heights and angles at the design stage for each zone, keeping heaters clear of vehicle lifts, cranes and doors.

Is infrared safe in a dusty or vehicle workshop?

Electric infrared has no flame and produces no combustion fumes. Heater choice and positioning depend on conditions such as dust, moisture or vehicle fumes, and we assess this at survey. Spray booths and areas with flammable vapours need specialist equipment, and we will tell you if any part of your building falls into that category.

Will our electrical supply cope?

We check your incoming supply and distribution board as part of the survey. If an upgrade or new circuits are needed, we tell you before you receive a quote, so there are no surprises.

How much will it cost to run?

Running costs depend on your building, how many zones are used, for how long and your electricity tariff. We don’t publish generic savings figures – we explain the expected running pattern for your design once we have assessed the building.

Can we keep working while you install?

In most cases, yes. We plan the installation around your working day and can phase it bay by bay where the workshop needs to stay open.

Can workshop heating run from solar panels?

Infrared heaters run on electricity, so daytime use can be supplied partly by on-site solar PV when it is generating. Solar output in Scotland is lower in winter, so we design the heating to work from the grid and treat solar as a contribution. See commercial solar PV & battery storage.

Do you heat home garages and workshops too?

Yes. The same survey and design approach applies to larger domestic garages and home workshops. See infrared heating for homes.

Related pages: Commercial infrared heating · Warehouse & industrial heating · Gym, studio & sports hall heating · Infrared heating for homes · Commercial solar PV

Get your workshop warm this winter

Tell us about your building – its size, ceiling height, how many people work there and when – and we will arrange a site survey and send you a heating design and quote. No obligation. Or call 0800 799 9753.